Installation TurboTec pulley wheel for Victory Motorcycles
Victory Motorcycle with 5-speed gearbox has gears that is a bit 'short. Rank first gear is almost non-usable and high is not high enough. These two teeth bigger slice makes your bike easier to use.
Victory 32 tooth Overdrive Pulley. Suitable for all motorcycles 03-05 Victor Victoria and 99-01's, with the delivery date. Revolutions this record decline of 7% and the use of all the original parts. I decided to install the pulley on my 2004 Victory Kingpinwrite step-by-step installation instructions with the installation images. Images are at the Victory Kingpin Cruisers site at the following link http://www.kingpincruisers.net/coppermine/thumbnails.php?album=56 can be seen. Here are my working notes for installation.
I did a second interview, and decided to bike on a jack.
It is not necessary to remove the wheel. I really want you to leave to help with the removal of the pinion.
I removed the slip-onPart of the activities prior to alleviate the drain.
Remove the group is waiting.
Remove the line on the right edge of the flat side so you can get out of the exhaust gas.
Before removing the exhaust.
Note the condition of the exhaust flange nuts.
Exhaust flange screws may be rusted. Spray with WD-40 and let stand overnight to loosen them up.
After this flange nuts, remove the exhaust.
Here's the Kingpin with everything removed.
Exhaust, tire covers, driverboard plan right side.
Wheel does not need to be removed. Indeed, must be installed to help with the removal of the pinion.
Remove the exhaust. The presentation in bottles is here somewhere.
With the exhaust, pulley cover remove pinion.
With Sprokect cover what you see now Sprocket.
Here I have the problem of the strap. Want friendly, and the wheel, because it acts as a resistance that is used when the die removiing Spock.
Another studylaw Kingpin completely stripped.
Remove the pinion plate locking screws and locking plates.
Remove the locking plate pinion.
Pinion nut requires a pinch of 48 millimeters.
Bolten has Loctited factory.
You can use a key to remove. Heat until the relaxation of Loctite.
Here I am with my heat gun. It took about 10-15 minutes when I could only hold the rear brake pedal and remove the nut.
Let cool pinion.
Willright slip.
Next, clean any residue off Loctite Gunk wires pinion shaft.
After removing the nut must be removed to loosen the belt, and the installation of the new Pully.
The crown will slip toward the bottom right loosening of the belt.
Here is the lone guard in the first leg of his new wheels.
Stay tuned for more because it's all as far as I have received. I have the new sprockets.
Bicycles must be pulled lower rightpanniers, passenger platforms, management of the driver and control, side cover for pulley, belt Covers (top and bottom) and remove the belt. The worst part of the work was the exhaust system, be careful with them. Here is a picture of your bike, ready to begin to bring them together again. Now everything clean remove and clean the Company and all areas that are exposed.
Grind the tab that contains the speed sensor. Grind about 3 / 8 's 1 / 4 "from the underside of the leaves, but not all the way tothe side of the engine block.
Pulley OD Keep trying until you go all the way out to save the loss. Coverage will also be set up final reel the approval of the belt. They rub off on the sleeve of the bolt.
With the installation of speed sensor used slices to a thickness of about 3 / 8 's 1 / 4 "put them in the screw hole, and then move the speed sensor on top of the washers, glue, nuts and turn.
Check the wheel alignment and belt tension. Withincreased on a mountain bike to rotate the wheel until you squint your belt – halfway between the front and rear pulleys. You should have about 9 millimeters flex with 10 pounds of force on the bottom. The signs on the swing arm is useless. When the voltage is set to spin the wheel and the harness adjustment strap watching the track on the front and rear pulleys. Belt rubbing on the edge of the rear sprocket is not.
Back to ultimately exhaust system. Be careful not to scratchtubes, as they maneuver into position.
Please, not the manufacturer of the disc Victory overdrive to make the installation instructions with their product does not contain. We hope these instructions help with installation. I found that very good help from the Kingpin Cruisers site to site http://www.KingpinCruisers.net. The installation requires a good pair of expertise tear, but as an integrated technology can do this, you will surely be able to do and much more work to do.